System Bootstrap, Version 5.2(5), RELEASE SOFTWARE Copyright (c) 1986-1994 by cisco Systems 2500 processor with 2048 Kbytes of main memory 大约停顿1-2分钟,系统调入boot,请耐心等待
F3: 3996764+54172+225404 at 0x3000060
Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706
Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-I-L), Version 11.2(1), MAJOR RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Mon 30-Sep-96 12:07 by ajchopra Image text-base: 0x030215A4, data-base: 0x00001000
cisco 2500 (68030) processor (revision D) with 2048K/2048K bytes of memory. Processor board ID 02327592, with hardware revision 00000000 Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read ONLY)
Notice: NVRAM invalid, possibly due to write erase. --- System Configuration Dialog ---
At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Would you like to enter the initial configuration dialog? [yes]:Return 你是否要进入初始化配置?默认"是".
First, would you like to see the current interface summary? [yes]:Return 首先,你是否想看一下当前端口的状态?默认"是".
Any interface listed with OK? value "NO" does not have a valid configuration 下面会列出当前路由器所具有的硬件配置(包括局域网口和广域网口,以及个端口当前状态等等.)
Interface IP-Address OK? Method Status Protocol Ethernet0 unassigned NO unset up down Serial0 unassigned NO unset down down Serial1 unassigned NO unset down down
Configuring global parameters:
Enter host name [Router]: JSRouter 设置系统名,如JSRouter.
The enable secret is a one-way cryptographic secret used instead of the enable password when it exists.
Enter enable secret: cisco 设置进入priviledged EXEC 的密码
The enable password is used when there is no enable secret and when using older software and some boot images.
Enter enable password: cisco1 (1) Enter virtual terminal password: cisco 设置进入虚拟终端登录到路由器的口令,即远程登录(telnet)的口令 Configure SNMP Network Management? [yes]:Return 是否设置简单网管协议? Community string [public]:Return
Configure IP? [yes]:Return 是否设置IP协议? Configure IGRP routing? [yes]:Return (2) 是否设置IGRP 路由协议? Your IGRP autonomous system number [1]:Return (3) 你的IGRP 路由协议自治系统号(AS),默认为1.
Configuring interface parameters: 下面配置端口参数
Configuring interface Ethernet0:Return Is this interface in use? [yes]:Return Configure IP on this interface? [yes]:Return IP address for this interface: 1.1.1.1 Number of bits in subnet field [0]:Return (4) Class A network is 1.0.0.0, 0 subnet bits; mask is /8 以上是配置以太口0,假设IP地址是1.1.1.1,掩码是255.0.0.0.
Configuring interface Serial0:Return Is this interface in use? [yes]:Return Configure IP on this interface? [yes]:Return Configure IP unnumbered on this interface? [no]:Return IP address for this interface: 2.1.1.1 Number of bits in subnet field [0]:Return Class A network is 2.0.0.0, 0 subnet bits; mask is /8 以上是配置串口0,假设IP地址是2.1.1.1,掩码是255.0.0.0.
网站地图
收藏本站
高级搜索
相关文章: